Our Line of Top Quality Vacuum Equipment

822 Hydro Vac

c/w Boom
Features

13m3 Hydro Vac c/w Boom
Complies with CSA B620, TC 407/412 – Current Edition

  • 13 cube capacity (9m3 debris and 4m3 water)
  • Hibon VTB 822XL – 2730 CFM Free air rating@ 27″ Hg maximum vacuum, PTO driven
  • 8” x 270 degree telescopic suction boom (Wirelessly controlled) mounted top rear of the debris tank
  • Custom Vac “in house” manufactured Aluminum 40″ Crossover cabinet (standard), heated and insulated with excellent interior and exterior lighting
  • Cat 3560 Pressure pump  (Rated 20 GPM @ 4000 PSI Max)
  • Hot Shot 980,000 BTU/hr Burner c/w Honeywell control, relief valves temperature
Configurations & Specs
Contact Sales
Rigged & Ready Trucks
HydroVac-822-Photo-002
HydroVac-822-Photo-001

Specs & Configurations

Standard Configuration

Debris Tank 9m3 (1980 Imp Gal +/- 3%)

  • 78″ Diameter
  • Pressure vessel hydrotested to 40 PSI
  • Full opening hydraulic lift rear door c/w locking style top hinge and 6 pin wheel door locks
  • Global hydraulic vibrator
  • Two recessed liquid level indicators D/S and P/S c/w indicator with grab handle
  • 3″ x 30 PSI pressure relief vent
  • Rear door top lock assembly and tank safety post
  • Operating Temperature -20 degrees F to 200 degrees F
  • 8″ Primary internal shutoff SS float ball and rubber seat assembly with 6″ flanged outlet

Water Compartment 4m3 (880 Imp Gal +/- 3%)

  • 20″ Manway
  • Recessed liquid level indicators on P/S c/w indicator with grab handle
  • 2″ Heated Breather, fill and suction c/w Riser/Vent Pipe
  • 2″ Heated Drain Valve c/w air actuated valve. Switch control at operator station
  • 2″ Heated stainless steel hard piped supply line, c/w composite loop hose and valve.  Direct connection through wash cabinet to wash pump
  • Catwalk, back rail and ladder D/S

8” Hydraulically Operated Boom (Wireless Operation)

  • 8” x 270 degree telescopic suction boom mounted top rear of debris tank
  • 12” knife gate valve assembly
  • Accumulator assembly
  • 8” boom hose with aluminum adapter
  • One wireless remote controller
  • One hard wired pendant control c/w cable and plug in
  • 6” Betts load valve c/w 6” sandpipe and aluminum camlock /cap D/S
  • 4” Betts load valve c/w aluminum camlock / cap P/S
  • 6” Betts discharge valve c/w aluminum camlock cap
  • All rear valves heated, air actuated and equipped with flip style valve controls
  • 8” piping c/w composite loop hose
  • 8” cyclone with bottom cleanout door and 2” heated drain valve
  • Two 2” pressure relief valve in blower exhaust pipe
  • Hibon VTB 822XL – 2730 CFM PD Blower. Oil Free Operation (Except Sealed Reservoirs) 27” Hg Maximum Vacuum
  • 8” Four-way diverter valve (vacuum to pressure mode)
  • 8” Double door check valve to prevent blower back spin
  • Diesel flush ball valve assembly
  • 20” pre-stage filter assembly c/w 20” filter

Wash Cabinet:

  • Custom Vac “in house” manufactured Aluminum 40″ Crossover cabinet (standard), heated and insulated with excellent interior and exterior lighting
  • Small door in large door for hose access P/S

Standard Wash System  (Access on Passenger Side):

  • Cat 3560 Pressure pump  (Rated 20 GPM @ 4000 PSI Max)
  • 2″ Stainless Steel strainer, 
  • Three Hydraulic Hose Reels (100′ x 3/8″ pressure hose, 100′ x 3/8″ temperature rated steam hose and a 100′ x 3/8″ degreaser hose).
  • Pressure trigger guns, wand, nozzle and quick coupler
  • Stainless Steel glycol and soap tanks  
  • Steam wand, nozzle and quick coupler
  • Degreaser assembly c/w gun, wand and nozzle 

Hot Water System:

  • Hot Shot 980,000 BTU/hr Burner c/w Honeywell control, relief valves temperature gauge Wet steam kit, Diagnostic panel
  • New Style 18 GPM Solid Brass Flow Switch with no bypass line
  • Safety feature: a Maximum 340 deg. Auto Shut-off on heater system
  • 3000 Pure Sine inverter to operate the burner assembly
  • Custom Vac aluminum vent hood is installed above the insulated stainless steel burner vent stack
  • Automatic louver assembly that opens when heater is ignited
  • Glycol Flush Tank /Air Blown System
  • Hard piped plumbing in Stainless Steel where applicable

Rig to Pull Pup (Standard)

  • Dog house
  • Recessed fitting boxes
  • Y pipe
  • Flip up bumper
  • Hydraulics as required c/w hose and fittings

Toolbox

  • One 60” W x 12” D x 17”H steel box c/w 2 access doors D/S

Paint / Coating

  • Entire tank and body of vacuum system will be sandblasted, primed and painted up to 2 colors
  • Water compartment internally lined

Frame, Decking, Trim

  • Full length 1/8” checker plate hose tray/fender assembly with heavy duty outrigger supports & 1-1/4” steel tubing handrails, close in plates
  • Ladder and platform P/S
  • Standard rear bumper
  • Slide out style chain hangers
  • Mud flaps c/w anti-sail brackets
  • 20 lb. fire extinguisher with mounting bracket and cover
  • 50’ ground cable c/w reel
Brochure
for Download
Custom Vac Hydro Vac 822 Brochure Cover
DOWNLOAD (PDF)