Straight Vac Unit - Customvac

Featured | Straight Vac

17 Cube – TC 407/412 and CSA B620-14

17 Cubes 3740 Imp Gal +3% Outage
Full opening hydraulic rear door, Hoist cylinder and Vibrator
Full length subframe c/w 1/8″ checkered mild steel/fender assembly, rear skirt and bumper
Robuschi RB-DV-85 PD High efficiency tri-lobe design Blower
6″ Plumbing, 6″ Cyclone with clean-out door & heated drain valve
6″ brass load valve with 6″ sandpipe D/S
Steel Vertical , deck cabinets & fitting boxes
D O T Lighting as required c/w L.E.D. work lights

Certified and Registered

Each design has been certified and registered with Transport Canada. This ensures that all of the required specifications have been achieved and are maintained thoughout the design and assembly process.

CONTACT SALES

For more information about customization, contact our sales representatives.

CONTACT SALES

UNITS AVAILABLE

Talk to us about any Rigged & Ready units we have available.

RIGGED & READY

Standard Configuration 17 Cube Straight Vac

Custom Vac CV85 Vacuum System (Tri-Drive Mounted).

DESIGN: Vessel designed and constructed in compliance to Transport Canada TC407/412 CSA B620-14

Debris Compartment

Debris Tank (17 Cubes 3740 Imp Gal +3% Outage):

78 Diameter x 17″
Long 78″ x 5/16
Heads 78″ x 5/16″ Shells

Four reinforcement rings
Three Rollover Bars
Tank Lock down assembly to meet current B620 Code
Reinforcing pads on all tank attachments
Pressure Vessel Hydro-tested to 40 PSI
Operating Temperature -20 deg F to 200 deg F
3″ x 30# PSIG Pressure Relief Vent
Preformed angle pedestals
Prep Tank for Gallup Agitator
8: heavy duty internal shut-off c/w 6″ stainless steel float ball/cage and rubber seat and 6″ flanged outlet
6″ Plumbing
Two 2″ PRV’S in lower suction pipe
6″ Composite Loop Hose Vic Clamped
One Bolted Baffle
Full Opening Hydraulic Lift Rear Door with Safety Device c/w 6 pinwheel door locks
Rear door safety post P/S
6″ Brass Load Valve with 6″ Sandpipe D/S
4″ Brass Load Valve P/S
6″ Brass Discharge Valve – Bottom Center of Rear Door
All rear valves heated and equipped with air/open, spring/close air actuators, separate flipper style control switches & aluminum camlocks
Recessed Stainless Steel Liquid Level Indicator – Grab Handle Style D/S
6″ Isolation Butterfly Valve – Air Control Switch at Operator Station
6″ Dip Port with Aluminum Camlock
6″ Cyclone with Clean-Out Door & Heated Drain Valve

Blower

Robuschi RB-DV-85 PD Vacuum Blower:

High Efficiency Tri-Lobe Design
1600 CFM Free Air Rating
27″ Hg Maximum Vacuum
Oil Free Operation (Except Sealed Reservoirs)
Blower Clearance & Timing Inspection Prior to Installation
6″ Four-Way Diverter Valve (Vacuum to Pressure Modes)
6″ Double Door Check Valve (To Prevent Blower Back Spin)
16″ Dia. x 20 Micron Rating (Washable) Pre-stage Blower Filter Approved Design
High Torque/High Temp Blower Drive Coupling with Flexible Insert
One Exhaust Silencer, One Intake Silencer

P T O:

8-Bolt P.T.O. (Greaseable Shaft Seal)
Air Shift Control & Hour Meter in Control Box by Driver’s Seat

Hydraulics

Hydraulic System (Linde Closed Loop Design):

Hydraulic Pump (Direct Mount to PTO)
Hydraulic Motor (Direct Mount to Blower)
Multi-function Hydraulic Control Bank
Variable Speed Joystick, for Blower Operation
Torque control for vac pressure
90 Imperial Gallon Hydraulic Oil Reservoir (Cleaned, Purged & Air Tested Prior to Installation) c/w (10 Micron) In tank Filter, Breather fill cap, Temperature & Level Indicator and inspection hatch
Global Hydraulic Vibrator with Flow Control Valve
One 12 Volt Oil Cooler
Mailhot 3-Stage Hydraulic Dump Cylinder
Double Acting Rear Door Hydraulic Cylinder with Safety Counter Balance Valve
Hydraulic Hose And Fittings As Required

DOWNLOAD SPECS

DOWNLOAD (PDF)