CSA B620-09 Hydrovac Detail

Features | Hydrovac

CU822 TC 407/412 CSA B620-14

  • 16 cube capacity 12m3 debris and 4m3 water
  • 6″ suction and discharge valves
  • 12 knife gate c/w 8″ hydraulic top mount boom
  • All valves are coded compliant full open hydraulic rear door
  • Robuschi -145 6400 CFM Free air rating@ 27″ Hg maximum vacuum.

Wash system

  • Wash system c/w cat 3560 triplex plunger pump
  • Hotshot 120 volt heater 980,000 BTU/hr
  • Hydraulic hose reels
  • Degreaser system
  • All equipment enclosed inside an insulated, heated aluminum enclosure
  • Code rear bumper and national safety mark

CONTACT SALES

For more information about customization contact our sales representative.

UNITS AVAILABLE

Talk to us about any Rigged & Ready units we may have available.

Standard Configuration – 822 Hydrovac

Custom Vac 822 Hydrovac has the following specifications (Tri-Drive Mounted):

Debris Compartment

Tank Design:

Vessel designed and constructed in full compliance with Transport Canada
TC 407/412 and CSA B620-09

  • Tank diameter 78″ (12′ seam to seam)
  • 78″ x 5/16″ F & D heads
  • 78″ x 5/16″ shells
  • Formed angle front & rear pedestals
  • Three 4″ roll bars
  • Three external reinforcement rings
  • Reinforcing pads for all tank attachments
  • Tank Lock Down Assembly to meet current B620 Code
  • 8″ Primary shut-off assembly with 8″ flanged outlet
  • 8″ isolation valve @ shut-off air actuated
  • Recessed liquid level indicator D/S
  • Full opening rear door c/w six pinwheel door locks
  • 6″Brass Suction valve c/w 6″ sandpipe, aluminum camlock/cap D/S
  • 4″Brass Suction valve c/w aluminum camlock and cap P/S
  • 12″ Hydraulic flange mounted mudgate with sliding lock mechanism and 4″
  • Brass valve with aluminum camlock and cap
  • All rear valves heated, and equipped with air/open- spring/close air actuators
  • control switches
  • Operating Temperature -20 deg F to 200 deg F
  • Vessel hydro tested to 40 PSI

Vibrator:

  • Global hydraulic vibrator assembly mounted on bottom of tank with reinforcement pads, heavy duty mounting channel and pressure relief valve.

Pressure Relief:

  • One 3″ x 30 PSIG pressure relief vent
  • One 2″ PRV in lower suction pipe
  • 2″ vacuum breakers installed on exhaust silencer

Gauges:

  • Gauge assembly with tank vacuum/pressure gauge, hydraulic pressure gauges.
  • Blower temperature gauge – remote mounted on D/S.

Blower

Blower Specifications & Allied Equipment:

  • Hibon SIAV 822
  • 2650 CFM free air rating
  • 27″ Hg Maximum Vacuum@ sea level
  • 8′ Four-Way Diverter valve ( Vacuum to Pressure Mode )
  • 8″ Double door check valve ( to prevent blower back spin )
  • Prestage filter assembly c/w 16″ filter
  • One intake silencer, One exhaust silencer
  • 8″ cyclone with bottom cleanout door & 2″ heated drain valve

Hydraulics

Hydraulic System (Linde closed loop design) :

  • 8 Bolt PTO for blower
  • 6 Bolt PTO for wash
  • Hydraulic pump and motor for blower
  • Hydraulic pump and motor for Triplex pump
  • Tandem gear pump for Auxiliary functions
  • High torque/temp drive coupler with flex insert
  • Spool type valve control bank for pump and allied functions
  • Rear control section for door and Dumpgate on deck  D/S
  • Joystick speed control for blowe
  • Torque control for vac pressure
  • 90 gallon oil tank c/w vent, site glass, filters, temperature gauge, and inspection hatc
  • Two 12 volt oil coolers
  • 3 stage hydraulic hoist cylinder

Boom:

  • 8″ x 270 deg telescopic suction boom
  • 12″ knife gate gate valve assembly with shear section
  • Accumulator for knife gate code compliance
  • 8″ boom hose with end
  • One wireless remote controller
  • One hard wired pendant controller for backup

Plumbing:

  • 8″ piping c/w 8″ oil & gas loop hose

Wash System

Wash System:

  • Cat 3560 Triplex plunger pump rated 20
  •  USGPM @ 4000 psi
  • 2″ Bronze strainer,1″ high pressure Baird relief valve,
  • Three Hydraulic Rewind Reels
  • 100′ x 1/2″ pressure hose
  • 100′ x 3/8″ temperature rated Steam hose
  • 100′ x 3/8″ degreaser hose
  • Note: Wash Systems Are Winterized for cold weather operation

Wash Accessories:

  • One wash gun, wand, nozzle and quick coupler
  • One steam wand, nozzle and quick coupler
  • One 6′ Hydro Dig Wand c/w 4′ extension and  Turbo Nozzle
  • One degreaser tank assembly c/w tank, stand, pump, gun, wand, and nozzle

Hot Water system:

  • Hotshot 980,000 BTU/hr heater c/w relief valves temperature gauge; Honeywell control ,Diagnostic panel
  • 2000 Watt Pure Sign Inverter
  • Wet Steam kit plumbed with high pressure ball valves
  • Safety Feature: a 340 deg. Auto Shut-Off on

Heater System

  • New style 18 GPM solid brass Flow Switch with no bypass line
  • All plumbing stainless steel

Wash Cabinet:

  • Milron Aluminum Crossover  cabinet c/w  Large doors D/S , P/S
  • Small access door in large door P/S for hose access
  • Heaters, LED Lights, and Auto Vent

Water Compartment (4 Cubes-880 Imp Gal):

  • 20″ top mounted Manway
  • Stainless steel liquid level indicator assembly P/S
  • 2″ heated fill, breather and suction
  • 2″ heated drain valve air actuated, Switch control at operator station
  • 2″ heated hard pipe supply direct connection through cabinet to triplex
  • 2″ heated Vac/water changeover valve air actuated

Equipment

Vibrator:

  • Global hydraulic vibrator assembly mounted on bottom of tank with reinforcement pads, heavy duty mounting channel and pressure relief valve

Pressure Relief:

  • One 3″ x 30 PSIG pressure relief vent
  • One 2″ PRV in lower suction pipe
  • 2″ vacuum breakers installed on exhaust silencer

Gauges:

  • Gauge assembly with tank vacuum/pressure gauge, hydraulic pressure gauges.
  • Blower temperature gauge remote mounted on D/S.

Frame, Deck and Bumper:

  • Full length subframe c/w 1/8″ checker plate hose tray/fender assembly
  • c/w heavy duty outrigger supports,1-1/4″ tube handrails, close in plate.
  • Code rear bumper with light boxes and rear tire skirt
  • Subframe supports decking, rear hoist hinges & front hoist cradle

Cabinets:

  • One steel 72″  three door deck box
  • Two rear skirt fitting boxes

Electrical System:

  • Waterproof main circuit control box self contained power supply
  • Sealed wire harness c/w waterproof junction boxes
  • L.E.D. lamps (Clearance, park, signal)
  • Sealed L.E.D. reverse lamps
  • Four L.E.D.  style work lights
  • L.E.D. WORK LIGHTS on the Boom Frame
  • Electrical system shut-down at key
  • Sealed rear skirt lamp modules
  • Stop and turn L.E.D sealed lamp modules on top ring of door.
  • Back up alarm
  • Truck cab and deck mount blower switches

Additional Equipment:

  • Catwalk & ladder on upper suction pipe driver’s side.
  • PTO Hour meter installed in truck cab
  • Chain hanger, slide out style
  • Mudflaps
  • 50′ ground cable (wind up style)
  • Ground studs mounted off rear peds D/S & P/S
  • 30# fire extinguisher/Brkt/Cover
  • Boom hose holders P/S
  • Two 6″ x 5″ aluminum dig tubes with Band Clamp ends one with rubber tip
  • One 8″ x  6″ x 4″ aluminum adapter

Paint:

  • The entire tank and body of vacuum system shall be sandblasted, primed and painted with Endura paint
  • Water Tank Lined With Devoe 233

Other Items:

  • Operators manual issued with completed unit
  • Unit includes (NSM) National Safety Mark
  • One year Manufacturer Ltd warranty